Rena T-350 Manuel d'utilisateur

T-350 Dual Tabber OPERATIONS MANUAL Revised: 3-23-09 Part # M-3435 RENA SYSTEMS INC. 136 Green Tree Road STE 140 Oaks, PA 19456-1069 Phone:

GETTING ACQUAINTED Control Panel 1. BATCH COUNTER – Counts tab cycles. The counter can be reset to zero, by pressing the small button on this

ASSEMBLY Section 2 – Assembly Stand-Alone Mode Note: This process assumes you will be using the system as a “stand-alone” tabber. Follow the steps

ASSEMBLY 4. Attach both Media Side Guides to the unit as shown. The bottom of the media side guide fits into the brass bushing, on the shaft, as

ASSEMBLY In-Line Mode Note: This process assumes you will be using the system as an “in-line” tabber. Follow the steps below to prepare the T-350 f

ASSEMBLY 4. Install the In-Line Roller Assembly. Install the flat end of the shaft first and then insert the pointed end of the sh

ASSEMBLY 6. Attach the Tab Box Tray. The hooks on the Tab Box Tray fit over the upper shaft, at the exit end of the tabber, as shown. The tray

ASSEMBLY External Feeder Control Setup CAUTION THIS PROCESS SHOULD BE PERFORMED BY A QUALIFIED SERVICE PERSON. PLEASE CONTACT YOUR LOCAL RENA SYST

ASSEMBLY Connecting the T-350 to an External Feeder Using the appropriate interface cable, attach the external feeder’s interface port to the T-35

ASSEMBLY Connecting Power 1. The T-350 is manufactured for use on a specific AC voltage source. Before connecting the power cord to the tabber;

OPERATING THE TABBER Section 3 – Operating the Tabber Theory of operation: The T-350 can be used as a “stand-alone” machine or an “in-line” mach

RENA Systems Inc. would like to Thank You for investing in our quality built products. Please record the following information for future referenc

OPERATING THE TABBER Loading/Threading Tabs: See the “Tab Stock Threading Diagrams” for additional help. 1. Remove the lid from the box of tab s

OPERATING THE TABBER Shaft6. Thread the tabs under the small shaft at the top of the tab drive assembly. Pull about 18 inches of tab stock out t

OPERATING THE TABBER 9. Bring the tab backing up around the back side of the Take-Up Spools and insert the end of the leader into the slit, in the

OPERATING THE TABBER 12. Using the peel bar locators; side the peel bar down to its “run position”. It should lock into position. IMPORTANT! When

OPERATING THE TABBER Tab Stock Threading Diagram (Peel Bar Up) This is the “threading position” for the peel bar. The peel bar must be in this po

OPERATING THE TABBER Tab Stock Threading Diagram (Peel Bar Down) This is the “run position” for the peel bar. The peel bar must be in this positi

OPERATING THE TABBER Setting Up the Feed System Sheet Separation Adjustment This procedure is used to insure that only one piece of media is fed

OPERATING THE TABBER Media Side Guide Adjustment 1. Adjust the Media Side Guides so that they are about a dimes width (~1/32-inch) from the sides

OPERATING THE TABBER Loading Media When placing media into the tabber, it is important to follow these steps. 1. Start by placing a single mail

OPERATING THE TABBER If you have a problem feeding the media, check the following: Feeding Doubles Reduce the distance between the separator finge

TABLE OF CONTENTS Table of Contents Section Page # SECTION 1 – GETTING ACQUAINTED ________________________________________________ 5 SAFE

OPERATING THE TABBER Adjusting the Tab Position Horizontal Tab Positioning The desired horizontal tab position is obtained by sliding the Tab Driv

OPERATING THE TABBER Tab Fold Position Adjustment The tab fold position is adjusted using the knob, located on the Media Sensor Assembly. IMPORTA

OPERATING THE TABBER NOTES _______________________________________________________________________ _____________________________________________

TROUBLESHOOTING Section 4 – Troubleshooting Tabbing Problems: Problem Possible Cause Tab Fold Placement Inconsistent  Tab Fold Adjustment Knob

TROUBLESHOOTING Media Feeding Problems: Problem Possible Cause Feeding Doubles  Media not properly fanned before loading.  Nested Media.  Re

TROUBLESHOOTING NOTES _______________________________________________________________________ __________________________________________________

MAINTENANCE Section 5 – Maintenance This section describes maintenance that an experienced operator can perform. If service or maintenance is need

MAINTENANCE Feed Rollers and Forwarding Rollers WARNING DO NOT USE SOLVENTS TO CLEAN THE RUBBER ROLLERS The feed and forwarding rollers can become

MAINTENANCE NOTES _______________________________________________________________________ _______________________________________________________

APPENDIX Appendix - Specifications T-350 Dual Tabber Dimensions: 10.5" W x 19" D x 15" H Speed: Up to 18,000 pieces per hour (8.5&q

TABLE OF CONTENTS NOTES _______________________________________________________________________ ________________________________________________

APPENDIX Appendix B – Obtaining Supplies, Service and Support Please contact your local Rena Systems Dealer to obtain supplies, service and support

APPENDIX NOTES _______________________________________________________________________ __________________________________________________________

INDEX INDEX A AC Power Inlet · 8 Assembly · 11 B Batch Counter · 10 C Choosing a Location · 17 Cleaning · 36 Connecting Power · 18 Contents · 6 Co

T Tab Box Tray · 6, 8 Tab Button · 10 Tab Drive Assemblies · 8 Tab Drive Assembly · 9 Tab Fold Adjustment Knob · 9 Tab Fold Position Adjustment · 3

Copyright © 2009 Rena Systems Inc All rights reserved

GETTING ACQUAINTED Section 1 – Getting Acquainted Safety Precautions THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. OBSERVE THE FOLLOWING

GETTING ACQUAINTED T-350 Operations Rev. 3/23/2009 6 Packaging/Shipping The Tabber is shipped in appropriate packaging so that, und

GETTING ACQUAINTED Introduction: The T-350 Tabber is a tabletop tabbing machine that is designed for the moderate volume user. It can be used “sta

GETTING ACQUAINTED Rear View TAB BOX TRAY AC POWER INLET FUSE HOLDER TAB DRIVE ASSEMBLIESPAPER SENSOR ASSEMBLY MAIN POWER SWITCH 1.

GETTING ACQUAINTED Tab Drive and Media Sensor Assembly Components PEEL BAR LOCATORTAB FOLD ADJUSTMENT KNOB PEEL BAR (down, run position) PEEL BAR